Got money to waste

GLEN #159 · #21 (**permalink**) 30-12-2008, 10:20 PM

Mark Your living in a dream land if you think you were pulling away from a Euro...

It's a matter of opinion as to which is the best direction at Lakeside... But we now run the direction we do as it was a safety issue and NBPBC care about safety, which is evident by what we do and the qualified paramedic in attendance at all times...

But Mark has somewhat of a point about 39cc bike revving harder... A 39cc bike is better for a long track as it revs harder... A 49cc bike is better for a short track as it produces more torque...

MortysMiniMotos · #22 (**permalink**) 30-12-2008, 10:32 PM

hmmm...

maybe except for the fact that mark pulled away from many euro bikes on his std chinese wtd in the elite races at the last round of the nationals?? and theres like photos of it and stuff....

funny part is the photos are of him on his dream bike which had NO bottom end and he's still infront of euro??? what the...

GLEN #159 · #23 (**permalink**) 30-12-2008, 10:35 PM

And this has what to do with the time he was at Lakeside???

MortysMiniMotos · #24 (**permalink**) 30-12-2008, 10:41 PM

nothing i guess... i just remembered a moment that i thought i should share...

i also assumed the bikes he was beating were alot quicker than your wrs...but hey...

morty · #25 (**permalink**) 30-12-2008, 10:42 PM

Glen, seriously... c'mon .. maybe you hadn't perfected your gearing.. (and that was your excuse at the time!) but I was lookin at you going up the hill and I was pullin away..!! pullin away!! I remember it like it was yesterday... don't worry, I remember it well enough for both of us bro!!!

K3PDMN · #26 (**permalink**) 31-12-2008, 12:18 PM

well use say to go with a 39cc though i wouldent know what parts to get or it cab reeds clutch crank.... and besides i can only buy parts from ebay

and basicly the only thing i can get there is reeds and a cab 4 it....

and yess i am aware that smaller cc motors revv higher

gas nitro cars rev to 40,000rmp

soo i think ima get the 45cc head kit, 19mm dellorto carbie,fiber glass reeds, and also exhaust heat wrap to stop oil leaking every where and wont look to bad i think ima stick with the clutch dont wanna buy a new 1 as it will cost more than everything i just bought

only got another $20 to spend:P

GLEN #159 · #27 (**permalink**) 31-12-2008, 01:17 PM

Dude, Exhaust heat wrap will not stop oil leaks...

What you need to get is, 'Permatex' brand, High Temp RTV Silicone Gasket Maker...

It is available from Super Cheap, Repco, AutoBarn, etc...

Exhaust 'heat wrap' is just that, to stop some of the exhaust heat radiating from it...

K3PDMN · #28 (**permalink**) 31-12-2008, 08:31 PM

oo well i got the rtv stuff any way:P is the heat wrap worth it its like 15 bucks lol

and what about the exhaust itself it comes from there and the joint i have the motor apart from the bike its in pieces just finished cleaning it im by it in like 20 min was supposed to get it yesterday but dident end up getting it

thanks for all your help hope to see u at the track some day:P

K3PDMN · #29 (**permalink**) 02-01-2009, 05:16 PM

kk bought it hopefully it will run nice and smooth

i ended up getting 19mm carb, 45cc head kit, fiber glass reed vales, pull start and the boost bottel:P

and i know use are gonna say its a waste but i got a friend using it and said it works so i thought id try it was that or 72 tooth rear sprocket^__^ (currently running a 68 tooth)

barnsey · #30 (**permalink**) 02-01-2009, 05:45 PM

what front sprocket you running??? if its a 6 you should have good bottom end
you may want to buy a jet kit and tune your bike a bit more
after you run it in

Got money to waste

Posted in Pocket Bike Performance Parts