hey everyone i'm new here.. i have one of these CAG bikes from ebay (yes i know quite cheap! )..
However when i give it gas now the bike just appears to rev and no movement.. when i took the clutch bell off and reseated it appears that the clutch wasn't rubbing the sides of the bell.. so i purchased a new clutch ( have had the bike for 6months or so now).. however now i still have the same problem, so i got another bell and still same problem bike just will not go.. i can lift the back tire up (not sitting on the bike) and rev it, which will turn the rear wheels however will make an awful grounding noise from the clutch rubbing the bell however not making complete contact with it..
anyone got any ideas on how to over come my issue??
you must be suffering a lot of clucth sippage.Where and how do you ride it.If yoy pussy foot around you damage the clucth.They are made to ride hard.
__________________
6 bikes.
-----------
one with RD top end kit.14/14 carby,carbon 3 stage fiber reeds,zx1 pipe
one with 55cc chainsaw top end, PBU pipe
ZX1 Taipan. PBU pipe,banshee engine.
Polini clutch bell .
2 X Banshees SHO
1 fitted with polini clutch,black widow triple stage reeds
19mm del rep carby,,billet head,billet reed cage, 6/76 gearing,sava tyres
1 fitted with 50cc BZM blata engine ,21mm walbro and BZM gold crank ( dangerous now:o)
1 blata SQ roller only SRT Spooge Racing Team NTH Division
I put a new clutch and new bell in and i'm still having the same problem.. i push off to start as per usual however it just doesn't want to move.. any ideas?? thx
drewdrewdrew wear did you get the new parts from.Is the clutch the same as the old one ,or did you put in an adjusable one.Is the bell the same size.They make differents sizes.eg 78mm 79 mm and 80mm.Might be the wrong bell.
__________________
6 bikes.
-----------
one with RD top end kit.14/14 carby,carbon 3 stage fiber reeds,zx1 pipe
one with 55cc chainsaw top end, PBU pipe
ZX1 Taipan. PBU pipe,banshee engine.
Polini clutch bell .
2 X Banshees SHO
1 fitted with polini clutch,black widow triple stage reeds
19mm del rep carby,,billet head,billet reed cage, 6/76 gearing,sava tyres
1 fitted with 50cc BZM blata engine ,21mm walbro and BZM gold crank ( dangerous now:o)
1 blata SQ roller only SRT Spooge Racing Team NTH Division
Yes thats right.As you rev up the engine the Clutch pads fly out and grab the bell.
__________________
6 bikes.
-----------
one with RD top end kit.14/14 carby,carbon 3 stage fiber reeds,zx1 pipe
one with 55cc chainsaw top end, PBU pipe
ZX1 Taipan. PBU pipe,banshee engine.
Polini clutch bell .
2 X Banshees SHO
1 fitted with polini clutch,black widow triple stage reeds
19mm del rep carby,,billet head,billet reed cage, 6/76 gearing,sava tyres
1 fitted with 50cc BZM blata engine ,21mm walbro and BZM gold crank ( dangerous now:o)
1 blata SQ roller only SRT Spooge Racing Team NTH Division
i c thankyou. do you know anywhere that sells a smaller bell then?
I am using the stock bell with a new clutch and have the same problem, so if i were to get a smaller bell it should catch..
I was reading on the forums last night people were saying to loosen the springs or something.. Is that a good idea so the clutch is already out a bit to grab when going? thx..
The clutch bell should be 78mm for an a/c cag,i wouldnt go buying any smaller or bigger.Have you made sure the clutch is secured on the crank shaft properly & tight and not slipping around on it,if it is the clutch wouldnt be doing anything and definately wouldnt be activating
Linear Mode
