Giant random parts sale

[Glen]

Hello, just did a cleanout and im getting rid of all the parts ill never need and are pointless to me now. just doing some prioritising as well so selling a few of the bikes.

Steering damper - was going on my dreambike but couldnt find a decent place to hide it. i have shaved down some of the bracket to get it to fit $15



Two coolant bottles used - one is from the original GP3 and the other a spare motor i purchased. no leaks - some crap in them from the original bikes. $10 for both.



Cag air filter. stock as a rock. $5



Cag pullstart with metal pawl. and two plastic pawls spare. one of the tabs is broken off the pullstart mount. make me an offer if you want.. Gone

[Glen]

two stock as a rock cag carbys with manifolds and mounting bolts. $10 each



78mm clutch bell. came from a dreambike/banshee motor. good when your clutches begin to wear down! as new. comes with an 8 tooth and 7 tooth pinion which are 6mm thread. $15




Cag clutch - only used to bed it in. complete with 10 turn springs installed. good upgrade! $15 SOLD

[Glen]

now this is an oddity! this is the stock dreambike clutch which has a very hard compound (much more so then a cag) and 10 turn springs, comes with a 10mm i believe straight hole for the stock dreambike crank. i was planning to countersink and taper the hole as a great upgrade to a cag. bedded in. $15



Cag fuel tank without the cap - just a stock kind. fits the GP3 replicas also. make me an offer on it or you can have it if you buy something else..



half a cag crankcase lol, good to practice porting on i guess.. free with another part or make me an offer. the other half shattered apart unfortunately..



Cag sprocket. 5mm thick i believe. 54 tooth. came off the etek cag bike. $5

[Glen]

stock dreambike crank. both lobes aligned and all fine. has the two keys already but there a little munged up so youd best punch them out and get two new ones. $30 it has the straight crank for the clutch so this would be good for banshee owners that want to run a proper euro clutch without the expense of getting the $300 euro crank.




17.5mm PHVA replica carb - stock on the banshee motors. has the lift choke. works great as i ran it on both my bzm dreambike and the gp3 replica. has an oval venturi so great for the blata motors or for a wide powerband. as new $40 - Sold pending payment

[Glen]

two watercooled 40cc pistons with ring / gudgeon pin bearing and clips. i cant recall the origins but i believe one came from the gp3 when i upgraded to a 5 port so it has only seen idle speed on the stand and the other is from the dreambike when i upped to the BZM so once more only idle on the stand and one ride up the road. both clean and no damage. $40



Stock dreambike Cylinder. 40cc 3 port. i have milled the piston skirt back to reduce restriction into the ports. comes with the replica head as well - no o rings in it. $40

[Glen]

stock dreambike / cag sprocket for the thin chain. approx 70 tooth. $5



cag throttle $5 or free with another part.

[Glen]

Cag quad - bought off a lady at my old workplace for $120 because the rear fairing was snapped and the engine wouldnt run. i have since got it going (coil was shitted along with the key being snapped) and it runs fantastic for a stock cag. i must say it is a petrifying ride for a grown up. so so unstable lol. pick up only for $150 - i may also chuck in a plethora of spare parts if they arent sold by the time this is.

i took the fairings off as they where fairly deadly with the sharp metal brackets and the like. great for kids.

comes with

- high performance flywheel
- 10 turn spring clutch
- Fibreglass reeds
- ported stock carb and air cleaner
- metal pullstart
- jetpro exhaust



some parts are still being installed but will be done by weeks end.

[Glen]

And last but not least my beloved GP3.

why am i getting rid of it? because this bike was for my sister to take up racing on - however she wants to step up to elite class so im putting my current dreambike motor into another bike and putting my full bzm in the dreambike.

The bike is a GRC RR replica with a 40cc 5 port reverse motor - the crankcase and cylinder have been ported which took 2 complete days to do.

runs a modified gearbox (the main gear has been lightened/ straighened and welded on as it was a press fit) and does not run in oil - sealed bearings. this is to make the gearbox setup much more free so it rotates so easily. the old setup was retarded with almost 5 seals in it for no reason.

Parts in the bike -

- blata radiator bottle
- 40cc 5 port head and cylinder
- Polini coil
- Polini water pump belt
- Zocchi chain
- custom CNC frame - 4kg lighter then the original.
- Polini pullstart
- Polini performance clutch cover
- Unifilter
- Polini blue reeds

The biggest point of this bike is the frame. i had this made by a company in china. it is 6061 Aluminium and solid. weight is approx 4kg lighter then the original. There is not another bike like this in the world! the front end is about 50mm longer then the original so its a great bike for the bigger person.

spare parts the bike will come with

- one complete spare frame and swingarm (the original)
- one complete motor sans carb
- one complete performance exhaust
- one complet stock exhaust (the header was modified)
- spare radiator
- Stock coil
- stock chain

the bike has a ballistic low end that will happily do in a stock banshee and its a great ride with the damper.

asking price is $1000 ONO including shipping i will get some videos of it running on request.

[Glen]

PM me or catch me on MSN if you want to make a deal or what not, cheers guys

[Glen]

ahhh found some more parts

stock flywheel - $10



stock head used for maybe 3 hours - $10 i can mill a big ass boost port into it for a couple more $$ if you wish.



and i have a stock cag crank with piston attached as well. no pics of that yet. $10